|
|
44's
Sept 11, 2005 17:41:29 GMT -3
Post by muddy88yj on Sept 11, 2005 17:41:29 GMT -3
I was wondering what it would take to put 44's on a 88 yj
|
|
|
|
44's
Sept 11, 2005 18:01:36 GMT -3
Post by dsgray16 on Sept 11, 2005 18:01:36 GMT -3
I would start off by getting rid of those D44's
I wouldnt run anything less then a 35spline 60 in the back, maybe even a 14bolt. And in the front a 35spline kingpin 60
And a D300 TC
thats a good start anyways...
|
|
|
|
44's
Sept 11, 2005 18:15:14 GMT -3
Post by dsgray16 on Sept 11, 2005 18:15:14 GMT -3
Also, welcome to the board! from your sig it sounds like you have a pretty sick jeep, yoiu got any pics?
|
|
|
|
44's
Sept 11, 2005 19:34:41 GMT -3
Post by jeepgod on Sept 11, 2005 19:34:41 GMT -3
most guys running 44s' are running full width 1 tons at a minuim! i know 2 guys running 44s' and they run rockwells! and they breal those axles also!
think long and hard about this one!
|
|
|
|
44's
Sept 11, 2005 23:35:04 GMT -3
Post by dsgray16 on Sept 11, 2005 23:35:04 GMT -3
kind of a strange firt post, maybe it was a joke???
|
|
|
|
44's
Sept 12, 2005 8:56:14 GMT -3
Post by jps4jeep on Sept 12, 2005 8:56:14 GMT -3
Welcome aboard
I would not run anything larger than 38's on well built D44's.
to accually put them uner your jeep, I assume you mean lift wise, $" springs and a SOA, a 3" body lift and a gratuidous amount of fender trimming. as well as larger axles. You can do It with a 2" lift spring SOA, but that will require the same fender trimming, and the use of uni-mog axles. they are a portal design and allow of lots of clearence stock.
|
|
|
|
44's
Sept 19, 2005 11:56:34 GMT -3
Post by muddy88yj on Sept 19, 2005 11:56:34 GMT -3
Thank you for your input and no it wasnt a joke. Not likely I will put 44' on my jeep but I alresdy have Adady 60 rear to build for my jeep
|
|
|
|
44's
Sept 19, 2005 12:11:14 GMT -3
Post by J.T.Woody on Sept 19, 2005 12:11:14 GMT -3
Thank you for your input and no it wasnt a joke. Not likely I will put 44' on my jeep but I alresdy have Adady 60 rear to build for my jeep Haha. I know this truck a little bit. You should see the D44 he blew up.  Hi Scott.  (friend of Mike's) |
|
|
|
44's
Sept 19, 2005 12:13:25 GMT -3
Post by muddy88yj on Sept 19, 2005 12:13:25 GMT -3
I also have a set of 38.5' to put on the jeep but they are on 15''rims 5on51/2 bolt pattern. My next question is if anyone knows of a break converson i could use to put the 38.5' on the dana 60 axle.
|
|
|
|
44's
Sept 19, 2005 12:35:59 GMT -3
Post by jps4jeep on Sept 19, 2005 12:35:59 GMT -3
is the D60 a full floater? is so, I venture no. I would go with the 8 lug anyways. looks meaner!
|
|
